安装完毕debian未能驱动网卡，内详。求大神笼罩，看贴的朋友也被好运笼罩（已解决）

[senwar]

1.本机安装 windows 7 .----- 剩余部分不分区，
2.cd 进去，自动划分区在未分区部分。
3.下面是 分区情况 见附件
4.下面是硬件详情
------[ 电脑配置概述信息 ]--------------------------------------------

计算机系统:
计算机类型 联想 ThinkCentre XXXX X86兼容台式电脑
操作系统 Windows 7 Ultimate(32bit)
DirectX版本 11.0 (4.09.00.0904)
Internet Explorer8.0 (8.0.7600.16385)

计算机硬件:
处理器(CPU) Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz
主板 联想 LENOVO
芯片组 英特尔 Q45/Q43 03
内存 2GB (Micron Technology PC3-8500F DDR3 SDRAM 1066MHz)
主硬盘 希捷 ST3320418AS(320GB, 7200转/分)
显卡 NVIDIA GeForce G100 (256 MB)
显示器 联想 LEN(17.1 英寸)
网卡 Intel(R) 82567LM-3 Gigabit Network Connection
声卡 SoundMAX Integrated Digital HD Audio

------ 以上数据由驱动人生[2.2.27]检测生成http://www.updrv.com ---------
5.问题详细情况

a，安装的时候就不能自动识别网卡，在列表里面也不能找到，我就选无网卡继续安装。。。。Orz....
B，进系统之后显示器显示：输入信号超出范围
C，一直没有网络
6.
debian@debian:~$ su
密码：
debian:/home/debian# sudo ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:63 errors:0 dropped:0 overruns:0 frame:0
TX packets:63 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:21985 (21.4 KiB) TX bytes:21985 (21.4 KiB)

debian:/home/debian# modprobe e1000e
debian:/home/debian# ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:157 errors:0 dropped:0 overruns:0 frame:0
TX packets:157 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:31261 (30.5 KiB) TX bytes:31261 (30.5 KiB)

debian:/home/debian#

7..

[ 0.083808] Capability LSM initialized
[ 0.083817] Mount-cache hash table entries: 512
[ 0.083907] Initializing cgroup subsys ns
[ 0.083910] Initializing cgroup subsys cpuacct
[ 0.083911] Initializing cgroup subsys devices
[ 0.083924] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.083926] CPU: L2 cache: 3072K
[ 0.083927] CPU: Physical Processor ID: 0
[ 0.083928] CPU: Processor Core ID: 0
[ 0.083931] Intel machine check architecture supported.
[ 0.083933] Intel machine check reporting enabled on CPU#0.
[ 0.083934] using mwait in idle threads.
[ 0.083941] Checking 'hlt' instruction... OK.
[ 0.100006] ACPI: Core revision 20080321
[ 0.111486] ENABLING IO-APIC IRQs
[ 0.111670] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.151284] CPU0: Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz stepping 0a
[ 0.152009] Booting processor 1/1 ip 6000
[ 0.160010] Initializing CPU#1
[ 0.160010] Calibrating delay using timer specific routine.. 5851.81 BogoMIPS (lpj=11703633)
[ 0.160010] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160010] CPU: L2 cache: 3072K
[ 0.160010] CPU: Physical Processor ID: 0
[ 0.160010] CPU: Processor Core ID: 1
[ 0.160010] Intel machine check architecture supported.
[ 0.160010] Intel machine check reporting enabled on CPU#1.
[ 0.240015] CPU1: Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz stepping 0a
[ 0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.244015] Brought up 2 CPUs
[ 0.244015] Total of 2 processors activated (11709.65 BogoMIPS).
[ 0.244015] CPU0 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 0 1
[ 0.244015] CPU1 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 1 0
[ 0.244015] net_namespace: 660 bytes
[ 0.244015] Booting paravirtualized kernel on bare hardware
[ 0.244015] NET: Registered protocol family 16
[ 0.244015] ACPI: bus type pci registered
[ 0.244015] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 16
[ 0.244015] PCI: MCFG area at f8000000 reserved in E820
[ 0.244015] PCI: Using MMCONFIG for extended config space
[ 0.244015] PCI: Using configuration type 1 for base access
[ 0.244015] Setting up standard PCI resources
[ 0.244015] ACPI: EC: Look up EC in DSDT
[ 0.248015] ACPI: Interpreter enabled
[ 0.248015] ACPI: (supports S0 S3 S4 S5)
[ 0.248015] ACPI: Using IOAPIC for interrupt routing
[ 0.252015] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.252015] PCI: Transparent bridge - 0000:00:1e.0
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG_._PRT]
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.256016] ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.256016] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.256016] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.256016] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.256016] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.256016] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.256016] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.256016] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.256016] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.260016] pnp: PnP ACPI init
[ 0.260016] ACPI: bus type pnp registered
[ 0.260016] pnp: PnP ACPI: found 13 devices
[ 0.260016] ACPI: ACPI bus type pnp unregistered
[ 0.260016] PnPBIOS: Disabled by ACPI PNP
[ 0.260016] PCI: Using ACPI for IRQ routing
[ 0.265206] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.265214] hpet0: 8 64-bit timers, 14318180 Hz
[ 0.269167] ACPI: RTC can wake from S4
[ 0.276092] system 00:01: ioport range 0x500-0x57f has been reserved
[ 0.276095] system 00:01: ioport range 0x800-0x80f has been reserved
[ 0.276099] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 0.276102] system 00:01: ioport range 0x1180-0x11bf has been reserved
[ 0.276105] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.276108] system 00:01: ioport range 0xfe00-0xfe00 has been reserved
[ 0.276112] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.276115] system 00:01: iomem range 0xf8000000-0xfbffffff could not be reserved
[ 0.276118] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.276123] system 00:01: iomem range 0xfed12000-0xfed12fff has been reserved
[ 0.276126] system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.276129] system 00:01: iomem range 0xfef00000-0xfeffffff has been reserved
[ 0.276133] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.276136] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.276139] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.276142] system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved
[ 0.276145] system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.307459] PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:01:00.0
[ 0.307459] PCI: Bridge: 0000:00:01.0
[ 0.307459] IO window: 2000-2fff
[ 0.307459] MEM window: 0xdd000000-0xdfffffff
[ 0.307459] PREFETCH window: 0x00000000e0000000-0x00000000efffffff
[ 0.307459] PCI: Bridge: 0000:00:1e.0
[ 0.307459] IO window: disabled.
[ 0.307459] MEM window: disabled.
[ 0.307459] PREFETCH window: disabled.
[ 0.307459] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.307459] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.307459] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.307459] NET: Registered protocol family 2
[ 0.320961] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.321150] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.321379] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.323088] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.323089] TCP reno registered
[ 0.330522] NET: Registered protocol family 1
[ 0.330624] checking if image is initramfs... it is
[ 0.507058] Switched to high resolution mode on CPU 1
[ 0.509952] Switched to high resolution mode on CPU 0
[ 0.651224] Freeing initrd memory: 6046k freed
[ 0.651224] Simple Boot Flag at 0x36 set to 0x1
[ 0.651600] audit: initializing netlink socket (disabled)
[ 0.651600] type=2000 audit(1281458895.640:1): initialized
[ 0.651600] highmem bounce pool size: 64 pages
[ 0.651600] Total HugeTLB memory allocated, 0
[ 0.651600] VFS: Disk quotas dquot_6.5.1
[ 0.651600] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.651600] msgmni has been set to 1751
[ 0.651600] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.651600] io scheduler noop registered
[ 0.651600] io scheduler anticipatory registered
[ 0.651600] io scheduler deadline registered
[ 0.651600] io scheduler cfq registered (default)
[ 0.651600] pci 0000:01:00.0: Boot video device
[ 0.651600] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.651600] assign_interrupt_mode Found MSI capability
[ 0.651600] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.651600] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.651600] isapnp: Scanning for PnP cards...
[ 1.003600] isapnp: No Plug & Play device found
[ 1.006014] hpet_resources: 0xfed00000 is busy
[ 1.006054] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.006175] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.006494] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.006579] ACPI: PCI Interrupt 0000:00:03.3 -> GSI 17 (level, low) -> IRQ 17
[ 1.006633] 0000:00:03.3: ttyS1 at I/O 0x1c88 (irq = 17) is a 16550A
[ 1.007422] brd: module loaded
[ 1.007476] PNP: PS/2 Controller [PNP0303:KBC0] at 0x60,0x64 irq 1
[ 1.007478] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.007599] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.007599] mice: PS/2 mouse device common for all mice
[ 1.007599] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.007599] rtc0: alarms up to one month, y3k
[ 1.007599] cpuidle: using governor ladder
[ 1.007599] cpuidle: using governor menu
[ 1.007599] No iBFT detected.
[ 1.007599] TCP cubic registered
[ 1.007599] NET: Registered protocol family 17
[ 1.007599] Using IPI No-Shortcut mode
[ 1.007599] registered taskstats version 1
[ 1.007599] rtc_cmos 00:05: setting system clock to 2010-08-10 16:48:16 UTC (1281458896)
[ 1.007680] Freeing unused kernel memory: 244k freed
[ 1.027600] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.059601] ACPI: SSDT 7EEBF887, 021F (r1 LENOVO TC-5C 139 INTL 20050228)
[ 1.059601] ACPI: SSDT 7EEBEE67, 067D (r1 LENOVO TC-5C 139 INTL 20050228)
[ 1.059601] Monitor-Mwait will be used to enter C-1 state
[ 1.059601] Monitor-Mwait will be used to enter C-2 state
[ 1.063600] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 1.063600] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.063600] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.063600] ACPI: SSDT 7EEBFAA6, 01B0 (r1 LENOVO TC-5C 139 INTL 20050228)
[ 1.063600] ACPI: SSDT 7EEBF4E4, 0085 (r1 LENOVO TC-5C 139 INTL 20050228)
[ 1.063601] ------------[ cut here ]------------
[ 1.063601] WARNING: at arch/x86/kernel/hpet.c:299 hpet_legacy_next_event+0x38/0x5a()
[ 1.063601] Modules linked in: processor(+) fan thermal_sys
[ 1.063601] Pid: 0, comm: swapper Not tainted 2.6.26-2-686 #1
[ 1.063601] [<c0122633>] warn_on_slowpath+0x40/0x66
[ 1.063601] [<c0134642>] ktime_get+0xd/0x21
[ 1.063601] [<c010f9eb>] apic_wait_icr_idle+0xe/0x15
[ 1.063601] [<c01190b2>] __resched_task+0x5c/0x5f
[ 1.063601] [<c010f9eb>] apic_wait_icr_idle+0xe/0x15
[ 1.063601] [<c01190b2>] __resched_task+0x5c/0x5f
[ 1.063601] [<c011b733>] try_to_wake_up+0xe8/0xf1
[ 1.063601] [<c01377b6>] clocksource_get_next+0x39/0x3f
[ 1.063601] [<c01367ae>] update_wall_time+0x519/0x68f
[ 1.063601] [<c0118511>] __wake_up_common+0x2e/0x58
[ 1.063601] [<c01140e3>] hpet_legacy_next_event+0x38/0x5a
[ 1.063601] [<c01388c0>] clockevents_program_event+0xc4/0xd2
[ 1.063601] [<c01395c2>] tick_dev_program_event+0x1e/0x82
[ 1.063601] [<c0139048>] tick_broadcast_set_event+0xf/0x11
[ 1.063601] [<c01392d2>] tick_broadcast_oneshot_control+0x8a/0xda
[ 1.063601] [<c0138d1e>] tick_notify+0x1cf/0x2e5
[ 1.063601] [<c0129b1f>] get_next_timer_interrupt+0x142/0x1aa
[ 1.063601] [<c0135004>] notifier_call_chain+0x2a/0x47
[ 1.063601] [<c0135048>] raw_notifier_call_chain+0x9/0xc
[ 1.063601] [<c01387c0>] clockevents_notify+0x19/0x55
[ 1.063601] [<f885a18e>] acpi_idle_enter_simple+0x89/0x203 [processor]
[ 1.063601] [<c024a18d>] cpuidle_idle_call+0x5b/0x86
[ 1.063601] [<c024a132>] cpuidle_idle_call+0x0/0x86
[ 1.063601] [<c01025d3>] cpu_idle+0xb0/0xd0
[ 1.063601] =======================
[ 1.063601] ---[ end trace 3cf7169d257728ec ]---
[ 1.063688] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 1.063710] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.063712] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.063601] Marking TSC unstable due to: TSC halts in idle.
[ 1.216537] usbcore: registered new interface driver usbfs
[ 1.216537] usbcore: registered new interface driver hub
[ 1.216537] usbcore: registered new device driver usb
[ 1.224538] USB Universal Host Controller Interface driver v3.0
[ 1.224538] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.224538] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.224538] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.224538] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.224538] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001840
[ 1.224538] usb usb1: configuration #1 chosen from 1 choice
[ 1.224538] hub 1-0:1.0: USB hub found
[ 1.224538] hub 1-0:1.0: 2 ports detected
[ 1.258770] No dock devices found.
[ 1.262771] SCSI subsystem initialized
[ 1.274318] libata version 3.00 loaded.
[ 1.287973] Floppy drive(s): fd0 is 1.44M
[ 1.306760] FDC 0 is a post-1991 82077
[ 1.330787] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.330787] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.330787] usb usb1: Product: UHCI Host Controller
[ 1.330787] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.330787] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.330787] ACPI: PCI Interrupt 0000:00:1a.1 -> GSI 17 (level, low) -> IRQ 17
[ 1.330787] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 1.330787] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.330787] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.330787] uhci_hcd 0000:00:1a.1: irq 17, io base 0x00001860
[ 1.330787] usb usb2: configuration #1 chosen from 1 choice
[ 1.330787] hub 2-0:1.0: USB hub found
[ 1.330787] hub 2-0:1.0: 2 ports detected
[ 1.434785] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.434785] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.434785] usb usb2: Product: UHCI Host Controller
[ 1.434785] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.434785] usb usb2: SerialNumber: 0000:00:1a.1
[ 1.434785] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.434785] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 1.434785] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.434785] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 1.434785] uhci_hcd 0000:00:1a.2: irq 18, io base 0x00001880
[ 1.434785] usb usb3: configuration #1 chosen from 1 choice
[ 1.434785] hub 3-0:1.0: USB hub found
[ 1.434785] hub 3-0:1.0: 2 ports detected
[ 1.538775] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.538775] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.538775] usb usb3: Product: UHCI Host Controller
[ 1.538775] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.538775] usb usb3: SerialNumber: 0000:00:1a.2
[ 1.538775] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.538775] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.538775] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.538775] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 1.538775] uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
[ 1.538775] usb usb4: configuration #1 chosen from 1 choice
[ 1.538775] hub 4-0:1.0: USB hub found
[ 1.538775] hub 4-0:1.0: 2 ports detected
[ 1.642775] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.642775] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.642775] usb usb4: Product: UHCI Host Controller
[ 1.642775] usb usb4: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.642775] usb usb4: SerialNumber: 0000:00:1d.0
[ 1.642775] ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 17 (level, low) -> IRQ 17
[ 1.642775] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 1.642775] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.642775] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 1.642775] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018c0
[ 1.642775] usb usb5: configuration #1 chosen from 1 choice
[ 1.642775] hub 5-0:1.0: USB hub found
[ 1.642775] hub 5-0:1.0: 2 ports detected
[ 1.746785] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.746785] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.746785] usb usb5: Product: UHCI Host Controller
[ 1.746785] usb usb5: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.746785] usb usb5: SerialNumber: 0000:00:1d.1
[ 1.746785] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.746785] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 1.746785] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.746785] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 1.746785] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018e0
[ 1.746785] usb usb6: configuration #1 chosen from 1 choice
[ 1.746785] hub 6-0:1.0: USB hub found
[ 1.746785] hub 6-0:1.0: 2 ports detected
[ 1.849787] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.849791] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.849793] usb usb6: Product: UHCI Host Controller
[ 1.849796] usb usb6: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.849798] usb usb6: SerialNumber: 0000:00:1d.2
[ 1.850275] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.850275] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 1.850275] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.850275] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
[ 1.854340] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.854340] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 1.854340] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc228000
[ 1.866371] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.866429] usb usb7: configuration #1 chosen from 1 choice
[ 1.866458] hub 7-0:1.0: USB hub found
[ 1.866464] hub 7-0:1.0: 6 ports detected
[ 1.970228] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.970231] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.970234] usb usb7: Product: EHCI Host Controller
[ 1.970236] usb usb7: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 1.970238] usb usb7: SerialNumber: 0000:00:1a.7
[ 1.973362] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.973362] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 1.973362] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.973362] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 1.974340] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.974340] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 1.974340] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xfc229000
[ 1.986972] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 1.998360] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.998416] usb usb8: configuration #1 chosen from 1 choice
[ 1.998435] hub 8-0:1.0: USB hub found
[ 1.998439] hub 8-0:1.0: 6 ports detected
[ 2.057156] hub 5-0:1.0: unable to enumerate USB device on port 1
[ 2.105098] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.105102] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.105104] usb usb8: Product: EHCI Host Controller
[ 2.105107] usb usb8: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 2.105109] usb usb8: SerialNumber: 0000:00:1d.7
[ 2.105161] ahci 0000:00:1f.2: version 3.0
[ 2.105187] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 17 (level, low) -> IRQ 17
[ 2.640140] usb 5-1: new low speed USB device using uhci_hcd and address 3
[ 2.807840] usb 5-1: configuration #1 chosen from 1 choice
[ 2.810186] usb 5-1: New USB device found, idVendor=04b3, idProduct=310c
[ 2.810190] usb 5-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 2.810193] usb 5-1: Product: USB Optical Mouse
[ 2.818340] usbcore: registered new interface driver hiddev
[ 2.833568] input: USB Optical Mouse as /class/input/input1
[ 2.833568] input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.1-1
[ 2.833568] usbcore: registered new interface driver usbhid
[ 2.833568] usbhid: v2.6:USB HID core driver
[ 3.107809] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0xd impl SATA mode
[ 3.107813] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp pio slum part
[ 3.107819] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 3.110837] scsi0 : ahci
[ 3.110837] scsi1 : ahci
[ 3.110837] scsi2 : ahci
[ 3.110837] scsi3 : ahci
[ 3.110837] scsi4 : ahci
[ 3.110838] scsi5 : ahci
[ 3.110838] ata1: SATA max UDMA/133 abar m2048@0xfc22a000 port 0xfc22a100 irq 222
[ 3.110838] ata2: DUMMY
[ 3.110838] ata3: SATA max UDMA/133 abar m2048@0xfc22a000 port 0xfc22a200 irq 222
[ 3.110838] ata4: SATA max UDMA/133 abar m2048@0xfc22a000 port 0xfc22a280 irq 222
[ 3.110838] ata5: DUMMY
[ 3.110838] ata6: DUMMY
[ 3.593455] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.593840] ata1.00: ATA-8: ST3320418AS, CC66, max UDMA/100
[ 3.593840] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 3.595746] ata1.00: configured for UDMA/100
[ 4.076289] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.076490] ata3.00: ATAPI: OPTIARC DVD-ROM DDU1681S, 1.93, max UDMA/100, ATAPI AN
[ 4.079254] ata3.00: configured for UDMA/100
[ 4.395655] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.395633] scsi 0:0:0:0: Direct-Access ATA ST3320418AS CC66 PQ: 0 ANSI: 5
[ 4.396870] scsi 2:0:0:0: CD-ROM OPTIARC DVD-ROM DDU1681S 1.93 PQ: 0 ANSI: 5
[ 4.406341] Driver 'sd' needs updating - please use bus_type methods
[ 4.406341] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 4.406341] sd 0:0:0:0: [sda] Write Protect is off
[ 4.406341] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.406341] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.406341] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 4.406341] sd 0:0:0:0: [sda] Write Protect is off
[ 4.406341] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.406355] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.406358] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 4.428376] sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 > sda3
[ 4.505417] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.513695] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 4.513695] Uniform CD-ROM driver Revision: 3.20
[ 4.513695] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 4.519444] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.519444] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 4.903692] PM: Starting manual resume from disk
[ 4.915962] kjournald starting. Commit interval 5 seconds
[ 4.915962] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.685748] udevd version 125 started
[ 5.908586] Linux agpgart interface v0.103
[ 6.431073] input: Power Button (FF) as /class/input/input2
[ 6.435740] ACPI: Power Button (FF) [PWRF]
[ 6.435843] input: Power Button (CM) as /class/input/input3
[ 6.439515] ACPI: Power Button (CM) [PWRB]
[ 6.447732] ACPI: WMI: Mapper loaded
[ 6.593132] input: PC Speaker as /class/input/input4
[ 6.604761] i801_smbus 0000:00:1f.3: enabling device (0001 -> 0003)
[ 6.604761] ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 17 (level, low) -> IRQ 17
[ 6.675892] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 6.675892] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 7.352365] Adding 2650684k swap on /dev/sda10. Priority:-1 extents:1 across:2650684k
[ 7.587903] EXT3 FS on sda3, internal journal
[ 8.258921] loop: module loaded
[ 9.169261] kjournald starting. Commit interval 5 seconds
[ 9.169405] EXT3 FS on sda12, internal journal
[ 9.169405] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.182700] kjournald starting. Commit interval 5 seconds
[ 9.183175] EXT3 FS on sda11, internal journal
[ 9.183175] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.200385] kjournald starting. Commit interval 5 seconds
[ 9.200544] EXT3 FS on sda8, internal journal
[ 9.200544] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.222754] kjournald starting. Commit interval 5 seconds
[ 9.223308] EXT3 FS on sda9, internal journal
[ 9.223308] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.686347] NET: Registered protocol family 10
[ 13.686347] lo: Disabled Privacy Extensions
[ 15.835347] lp: driver loaded but no devices found
[ 15.871367] ppdev: user-space parallel port driver
[ 269.842146] usb 7-2: new high speed USB device using ehci_hcd and address 2
[ 269.986184] usb 7-2: configuration #1 chosen from 1 choice
[ 269.986184] usb 7-2: New USB device found, idVendor=0930, idProduct=6545
[ 269.986184] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 269.986184] usb 7-2: Product: DataTraveler 2.0
[ 269.986184] usb 7-2: Manufacturer: Kingston
[ 269.986184] usb 7-2: SerialNumber: 5B820D00004C
[ 270.054169] Initializing USB Mass Storage driver...
[ 270.054169] scsi6 : SCSI emulation for USB Mass Storage devices
[ 270.054173] usbcore: registered new interface driver usb-storage
[ 270.054173] USB Mass Storage support registered.
[ 270.054173] usb-storage: device found at 2
[ 270.054173] usb-storage: waiting for device to settle before scanning
[ 275.080293] usb-storage: device scan complete
[ 275.107611] scsi 6:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 275.330074] sd 6:0:0:0: [sdb] 3903488 512-byte hardware sectors (1999 MB)
[ 275.330621] sd 6:0:0:0: [sdb] Write Protect is off
[ 275.330621] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 275.330621] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 275.334083] sd 6:0:0:0: [sdb] 3903488 512-byte hardware sectors (1999 MB)
[ 275.335619] sd 6:0:0:0: [sdb] Write Protect is off
[ 275.335619] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 275.335619] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 275.335619] sdb: sdb4
[ 275.377696] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 275.377696] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 275.726943] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
debian:/home/debian#

[davidlone]

代码： 全选

sudo ifconfig eth0 up

有效不，按理说这个网卡应该能自动加载驱动的啊
下面是最新版的驱动

e1000e-1.2.10.tar.gz

(232.1 KiB) 已下载 82 次

[senwar]

代码： 全选

sudo ifconfig eth0 up

有效不，按理说这个网卡应该能自动加载驱动的啊
下面是最新版的驱动

e1000e-1.2.10.tar.gz

求写一个详细的安装过程,我吃菜鸟来的.
接触linux 才 12 小时, O(∩_∩)O谢谢!

[senwar]

1. 把这个tar文件拷贝到用户自己定义的目录中,例如:
/home/username/e1000 or
2. 用tar命令解这个压缩包:
tar zxf e1000e-1.2.10.tar.gz
3. 切换到驱动的src目录下:
cd e1000e-1.2.10/src/

已经做到这步了！

4. 编译这个驱动模块:
make

这个命令怎么使？ 还要带什么参数或者文件名 路径？

然后安装这个模块
make install

这个命令怎么使？ 还要带什么参数或者文件名 路径？

5. 安装模块:
insmode1000e
这个命令怎么使？ 还要带什么参数或者文件名 路径？
不知道是不是这样!

[august.seu]

首先，你的将你网卡的型号找出来，
dmesg | grep eth0

把内容贴出来

[清荷听雨]

下载最新的驱动，安装上就可以了，我的也是这个问题。