笔记本硬盘的ahci-ncq模式

[kovchou]

我的硬盘在Ubuntu下奇热，在Vista下还好，不知道是不是AHCI的问题，
Y450的机子

[opp]

[ 0.952378] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
[ 0.952382] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
[ 0.952386] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
[ 0.952389] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
[ 0.952393] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f300 irq 22
[ 0.952397] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f380 irq 22
[ 0.952653] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.952767] scsi6 : pata_atiixp
[ 0.952824] scsi7 : pata_atiixp
[ 0.953669] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
[ 0.953672] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
[ 1.272079] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.272108] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.272135] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.272161] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.272188] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.436020] ata1: softreset failed (device not ready)
[ 1.436024] ata1: applying SB600 PMP SRST workaround and retrying
[ 1.600029] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.626902] ata1.00: ATA-8: ST3500410AS, CC34, max UDMA/133
[ 1.626905] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.666264] ata1.00: configured for UDMA/133
[ 1.836515] Write protecting the kernel read-only data: 1836k
[ 3.048378] EXT4-fs (sda9): mounted filesystem with ordered data mode
[ 14.947701] EXT4-fs (sda8): mounted filesystem with ordered data mode
[ 15.031550] EXT4-fs (sda10): mounted filesystem with ordered data mode
我的台式机啊，也可以开戾AHCI模式，不知道我这样的开启了没有。呵呵。

[yedahao]

搞定了，原来要加上ahci驱动~~

怎么加啊??教教...我在用WIN7已经开了AHCI在AHCI下安装UBUNTU..装完之后..进不了..WIN7也一起进不了..换回IDE..才可以进..再删了UB..WIN7再开AHIC..又可以了..怎么搞...

[warmsun]

楼主怎么加驱动啊？？我用AHCI也是开机慢的要命 详细说说呗 这么多人问呢